View LTL4HMYS8DS-032A_9035529.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lite-on dcc release bns-od-fc001/a4 lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto through hole lamp product data sheetLTL4HMYS8DS-032A spec no. :ds20-2017-0042effective date: 04/06/2017 revision: -
1 / 10 part no. : ltl 4hm y s8 d - 032a (only for chemito controls) bns - od - fc002/a4 through hole lamp LTL4HMYS8DS-032A (only for chemito controls) through hole lamp LTL4HMYS8DS-032A (only for chemito controls) rev description by date p001 preliminary spec(rdr-20150090-02) craig 03/31/ 2015 p002 revise va spec. craig 01/14/2016 above data for pd and customer tracking only - nppr received and upload on opnc nick 03/29/2017
2 / 10 part no. : ltl 4hm y s8 d - 032a (only for chemito controls) bns - od - fc002/a4 through hole lamp LTL4HMYS8DS-032A (only for chemito controls) 1. description 4mm oval lamp is a new design with a smoother wide view angle radiation pattern suitable in full color signboard, billboard sign, message sign and bus sign. high luminous inte nsity output has a higher emitting efficiency to sa ve power energy. advance d epoxy technology has a good moisture resistance a nd uv protection to be used in package, and it can reduce the effect of long term exposure in outdoor environment . 1. 1. features high luminous intensity output. low power consumption & high efficiency. superior resistance to moisture good uv inhibitor lead free & rohs compliant 4mm oval amber alingap 590nm lamp & amber diffused typical viewing angle 120 x 80 1.2. applications message sign traffic sign bus sign 2. outline dimensions notes : 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm (.010") unless otherwise noted . 3. protruded resin under flange is 1.0mm (.04") max. 4. lead spacing is measured where the leads emerge fro m the package. 5. specifications are subject to change without notice .
3 / 10 part no. : ltl 4hm y s8 d - 032a (only for chemito controls) bns - od - fc002/a4 through hole lamp LTL4HMYS8DS-032A (only for chemito controls) 3. absolute maximum ratings at ta=25 parameter maximum rating unit power dissipation 125 mw peak forward current (duty cycle Q 1/10, pulse width Q 10ms) 100 ma dc forward current 50 ma derating linear from 50 0.64 ma/ reverse voltage 5 v operating temperature range -30c to + 85c storage temperature range -40c to + 100c lead soldering temperature [2.0mm (.079") from body] 260c for 5 seconds max. 4. electrical / optical characteristics at ta=25 parameter symbol min. typ. max. unit test condition luminous intensity iv 1800 2500 3200 mcd if = 20ma note 1,4 viewing angle 2 1/2 120/80 deg note 6 (fig.6) peak emission wavelength p 596 nm measurement @peak (fig.1) dominant wavelength d 590 595 nm note 3 spectral line half-width ? 17 nm forward voltage vf 1.8 2.4 v if = 20ma reverse current ir 50 a vr = 5v note: 1. luminous intensity is measured with a light sens or and filter combination that approximates the cie eye-response curve. 2. iv classification code is marked on each packing bag. 3. the dominant wavelength, d is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 4. iv guarantee must be included with 25% testing tolerance. 5. reverse voltage (vr) condition is applied for ir test only. the device is not designed for reverse operation. 6. view angle measurement is 2 degree tolerance.
4 / 10 part no. : ltl 4hm y s8 d - 032a (only for chemito controls) bns - od - fc002/a4 through hole lamp LTL4HMYS8DS-032A (only for chemito controls) 5. typical electrical / optical characteristics cur ves (25 ambient temperature unless otherwise noted)
5 / 10 part no. : ltl 4hm y s8 d - 032a (only for chemito controls) bns - od - fc002/a4 through hole lamp LTL4HMYS8DS-032A (only for chemito controls) 6. taping features * compatible with radial lead automatic insertion e quipment. * most radial lead plastic lead lamps available pac kaged in tape and folding. * 2.54mm (0.1") straight lead spacing available. * folding packaging simplifies handling and testing . * reel packaging is available by removing suffix a on option. package dimensions specification item symbol minimum maximum mm inch mm inch tape feed hole diameter d 3.8 0.149 4.2 0.165 component lead pitch f 2.3 0.091 3.0 0.118 front to rear deflection h -- -- 2.0 0.078 feed hole to bottom of component h1 20.0 0.787 21.0 0.827 feed hole to overall component height h2 26.0 1.024 27.6 1.087 lead length after component height l w0 11.0 0.433 feed hole pitch p 12.4 0.488 13.0 0.511 lead location p1 4.4 0.173 5.8 0.228 center of component location p2 5.05 0.198 7.65 0.301 total tape thickness t -- -- 0.90 0.035 feed hole location w0 8.5 0.334 9.75 0.384 adhesive tape position w2 0 0 3.0 0.118 tape width w3 17.5 0.689 19.0 0.748
6 / 10 part no. : ltl 4hm y s8 d - 032a (only for chemito controls) bns - od - fc002/a4 through hole lamp LTL4HMYS8DS-032A (only for chemito controls) 7. packing spec. total 2,000pcs per inner carton 10 inner cartons per outer carton total 20,000 pcs per outer carton in every shipping lot, only the last pack will be non-full packing
7 / 10 part no. : ltl 4hm y s8 d - 032a (only for chemito controls) bns - od - fc002/a4 through hole lamp LTL4HMYS8DS-032A (only for chemito controls) 8. bin table specification luminous intensity iv (mcd) if@20ma bin code min. max. s 1800 2500 t 2500 3200 note: tolerance of each bin limit is 25% forward voltage unit : v @20ma/25?c bin code min max 1 1.8 2.0 2 2.0 2.2 3 2.2 2.4 note: tolerance of each bin limit is 0.1v
8 / 10 part no. : ltl 4hm y s8 d - 032a (only for chemito controls) bns - od - fc002/a4 through hole lamp LTL4HMYS8DS-032A (only for chemito controls) 9. cautions 9.1. application this led lamp is good for application of indoor and outdoor sign, also ordinary electronic equipment. 9.2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is re commended that leds out of their original packaging are used withi n three months. for extended storage out of their o riginal packaging, it is recommended that the leds be stored in a sealed con tainer with appropriate desiccant or in desiccators with nitrogen ambient. 9.3. cleaning use alcohol-based cleaning solvents such as isoprop yl alcohol to clean the leds if necessary. 9.4. lead forming & assembly during lead forming, the leads should be bent at a point at least 3mm from the base of led lens. do no t use the base of the lead frame as a fulcrum during forming. lead formin g must be done before soldering, at normal temperat ure. during assembly on pcb, use minimum clinch force possible to avoid excessive mechanical stress. 9.5. soldering when soldering, leave a minimum of 3mm clearance fr om the base of the lens to the soldering point. dip ping the lens into the solder must be avoided. do not apply any external s tress to the lead frame during soldering while the led is at high temperature. recommended soldering conditions: soldering iron wave soldering temperature soldering time position 350c max. 3 seconds max. (one time only) no closer than 2mm from the base of the epoxy bulb pre-heat pre-heat time solder wave soldering time dipping position 100c max. 60 seconds max. 260c max. 5 seconds max. no lower than 2mm from the base of the epoxy bulb note: excessive soldering temperature and/or time m ight result in deformation of the led lens or catas trophic failure of the led. ir reflow is not suitable proce ss for through hole type led lamp product. 9.6. drive method an led is a current-operated device. in order to en sure intensity uniformity on multiple leds connecte d in parallel in an application, it is recommended that a current limit ing resistor be incorporated in the drive circuit, in series with each led as shown in circuit a below. circuit model (a) circuit model (b) (a) recommended circuit (b) the brightness of each led might appear differe nt due to the differences in the i-v characteristic s of those leds. led led
9 / 10 part no. : ltl 4hm y s8 d - 032a (only for chemito controls) bns - od - fc002/a4 through hole lamp LTL4HMYS8DS-032A (only for chemito controls) 9.7. esd (electrostatic discharge) static electricity or power surge will damage the l ed. suggestions to prevent esd damage: use a conductive wrist band or anti- electrostatic glove when handling these leds all devices, equipment, and machinery must be prop erly grounded work tables, storage racks, etc. should be properl y grounded use ion blower to neutralize the static charge whi ch might have built up on surface of the leds plast ic lens as a result of friction between leds during st orage and handing suggested checking list: training and certification 9.7.1.1. everyone working in a static-safe area is esd-certified? 9.7.1.2. training records kept and re-certific ation dates monitored? static-safe workstation & work areas 9.7.2.1. static-safe workstation or work-areas have esd signs? 9.7.2.2. all surfaces and objects at all stati c-safe workstation and within 1 ft measure less tha n 100v? 9.7.2.3. all ionizer activated, positioned toward s the units? 9.7.2.4. each work surface mats grounding is g ood? personnel grounding 9.7.3.1. every person (including visitors) han dling esd sensitive (esds) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 9.7.3.1. if conductive footwear used, conductive flooring also present where operator stand or walk? 9.7.3.2. garments, hairs or anything closer th an 1 ft to esd items measure less than 100v*? 9.7.3.3. every wrist strap or heel strap/condu ctive shoes checked daily and result recorded for a ll dls? 9.7.3.4. all wrist strap or heel strap checker s calibration up to date? note: *50v for blue led. device handling 9.7.4.1. every esds items identified by eia-47 1 labels on item or packaging? 9.7.4.2. all esds items completely inside prop erly closed static-shielding containers when not at static-safe workstation? 9.7.4.3. no static charge generators (e.g. pla stics) inside shielding containers with esds items? 9.7.4.4. all flexible conductive and dissipati ve package materials inspected before reuse or recy cle? others 9.7.5.1. audit result reported to entity esd co ntrol coordinator? 9.7.5.2. corrective action from previous audit s completed? 9.7.5.3. are audit records complete and on file ?
10 / 10 part no. : ltl 4hm y s8 d - 032a (only for chemito controls) bns - od - fc002/a4 through hole lamp LTL4HMYS8DS-032A (only for chemito controls) 10. reliability test classification test item test condition sample size reference standard endurance test operation life ta = 25c if = 30ma test time= 1000hrs 45 pcs (cl=90%; ltpd=5%) mil-std-750d:1026 (1995) mil-std-883g:1005 (2006) high temperature high humidity storage (thb) ta = 85c rh = 85% test time= 1000hrs 45 pcs (cl=90%; ltpd=5%) mil-std-202g:103b (2002) jeita ed-4701:100 103 (2001) steady state operation life of high humidity heat ta = 85c, rh= 85 % if = 15ma test time= 500hrs 76 pcs (cl=90%; ltpd=3%) jesd22-a101c (2009) low temperature operation life of ta = -30c if = 30ma test time= 1000hrs 45 pcs (cl=90%; ltpd=5%) high temperature storage ta= 105 5c test time= 1000hrs 45 pcs (cl=90%; ltpd=5%) mil-std-750d:1031 (1995) mil-std-883g:1008 (2006) jeita ed-4701:200 201 (2001) low temperature storage ta= -55 5c test time= 1000hrs 45 pcs (cl=90%; ltpd=5%) jeita ed-4701:200 202 (2001) environmental test temperature cycling 100c 25c -40c 25c 30mins 5mins 30mins 5mins test time: 200 cycles 76 pcs (cl=90%; ltpd=3%) mil-std-750d:1051 (1995) mil-std-883g:1010 (2006) jeita ed-4701:100 105 (2001) jesd22-a104c (2005) thermal shock 100 5c -30c 5c 15mins 15mins test time: 200 cycles 76 pcs (cl=90%; ltpd=3%) mil-std-750d:1056 (1995) mil-std-883g:1011 (2006) mil-std-202g:107g (2002) jesd22-a106b (2004) solder resistance t.sol = 260 5c dwell time= 101 seconds 3mm from the base of the epoxy bulb 11 pcs (cl=90%; ltpd=18.9%) mil-std-750d:2031(1995) jeita ed-4701: 300 302 (2001) solderability t. sol = 245 5c dwell time= 5 0.5 seconds (lead free solder, coverage R 95% of the dipped surface) 11 pcs (cl=90%; ltpd=18.9%) mil-std-750d:2026 (1995) mil-std-883g:2003 (2006) mil-std-202g:208h (2002) ipc/eia j-std-002 (2004) soldering iron t. sol = 350 5c dwell time= 3.5 0.5 seconds 11 pcs (cl=90%; ltpd=18.9%) mil-std-202g:208h (2002) jeita ed-4701:300 302 (2001) 11. others the appearance and specifications of the produ ct may be modified for improvement, without prior n otice.

▲Up To Search▲

Price & Availability of LTL4HMYS8DS-032A

	To Download LTL4HMYS8DS-032A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .